Pages

Showing posts with label Axle Plate. Show all posts
Showing posts with label Axle Plate. Show all posts

Saturday, May 10, 2014

Royal Enfield Chopper in progress...Continues


I started to rebuild my springer. It has lots of free play here and there and those springer rods are bend little bit + they have bad threads. What I found from internet, were little bit too short for me also, so I decided to do them by myself. I will do Sugar Bear style rockers to springer too. More about that later.

Old ones


First I did some lathe job to axle steel bar


I read this trick, that you can put thread cutter directly to tailstock, tighten it and then just rotate chuck by had. Did not work for me, thread cutter does not stay at place.


I had to keep cutter still with other hand, add little bit pressure from back and rotate chuck by hand.


Worked! Only 3 more left. This is good method, since you get cutter straight to bar.


One side ready.


Then I did some spacer, so that the upper springs don´t move when tightened. First I cutted away some stuff from bigger nut with lathe.




Then took material out from too narrow spacer


Here they are, ready to be together. 



I am happy with results.



Fits fine. Also modified nut goes inside the spring, so it keeps it straight



There they are. Have to do something for the bottom end of the upper spring also, so it stays in line.


Here is pictures of my new hard tail. It is made from 25*3mm hydraulic tube & TIG welded together.

Yes. We did had a jig...


And here it is, all welded & ready to go with me. We did errors that much, that instead of using about 3 meters of tube, we used at least 5 meters! Errors happened and WILL happen in future also!











Saturday, April 12, 2014

My Dodge did NOT pass the inspection. Reasons were:

- left upper ball joint have to be changed
- both tie rod ends have to be changed
- right brake at back is not taking enough

Not bad! Also there was strange thing that showed up. The pollution test, which I did at another place was not valid! Now the inspection guy said, that I have to make it again at THEIR place and pay 17€ for that or otherwise he will fail whole inspection right away. Ok. He took it, and it passed again. There were minor difference in oxygen level with this test compared to earlier. Still I wonder how this went like it went. I should have said him that he inspects the car otherwise and if it fail, why I should bother to take HIS pollution test. But it is too late now. As usual, you understand later, what you should have said. Anyway. Now I have one month to repair those problems. If I don´t my inspection fails and it have to start all over again.

After these things I went to my friends work place and we started to do rear end for Royal Enfield.


Upper tubes are now welded to axle plates and we can continue next friday. It takes long for this rear end to be completed, since this has to be done at my friends workplace, because there they have TIG. Bad thing is that we can use it only at fridays. Still few months to summer...


While my friend was welding, I finalized lower tube mountings, whose I started at home. Look the difference of thickness between old and new. Old are modified from original RE mountings. New are copies of modified originals!


Mounting place


Upper - old, lower -new





Wednesday, March 19, 2014

This is how He looks now...One upper tube welded little bit, but I´ll have to remove it, since I did new axle plates...This is how I work (stupidly). I start something and then notice, that I should have thought more...But that´s the way it is...I build with inspiration, not by planning everything perfect beforehand. Not best or fastest way to work!


It did new axle plates with my disc grinder. Copied model from here: Chopper Axle Plates (Hardtail Axle Plates) and printed it + started to cut on 10mm mild steel. Thanks for model for Travis. Hopefully you don´t feel that I stole your model. I just did not had money to order yours. All honour for design to him.


Grinding started


Almost there. Now have to wait that I get step drill bit to drill holes into these.


Old and new. Quite improvement, I´d say.